Adding text with variable on several files

Alan Kilborn

I suppose something like this works:

Set search mode to Regular expression

find:

(?-s)^HEADER(\R)\R(?=party = {\Rname = "(...)_section_four")

replace:

HEADER${1}${1}party = {${1}name = "${2}_section_one"${1}62194678${1}${1}party = {${1}name = "${2}_section_two"${1}112093${1}${1}party = {${1}name = "${2}_section_three"${1}87321345

Vincent Perez

@Alan-Kilborn Is not finding it

Alan Kilborn

@Vincent-Perez

You may need to adjust your double-quote characters in the “find” and “replace” expression I gave.

If you look closely at your screenshot data, you’ll see that yours are “slanted” and I used “straight” in my expressions. They are not interchangeable – welcome to a unicode world.

I did what I did because you pasted data into this site without preserving its format, so I made my “best guess” at what you had.

Or, it could be something else wrong.
But…I’d start there.

Vincent Perez

@Vincent-Perez said in Adding text with variable on several files:

“ALE_section_one”

You were right! thank you very much, you have saved me a lot of hours of boring copy paste :-)

guy038

Hi, @vincent-perez, @alan-kilborn and All,

If I suppose that your text contains, after the HEADER line, n blocks as below ( syntax xxx means any text ) :


party = {
name = "s%_section_xxx"
xxxxx

In turn, followed with m blocks as below :


party = {
name = "XXX_section_xxx"
xxxxx

And if m is greater than 0 ( i.e. if exists, at least, one block with a line name = "XXX_section_xxx" where the string XXX must replace the string s% )

An other solution could be :

SEARCH (?s-i)s%(?=.*?^name\x20=\x20"(\w+)_section)

REPLACE \1

Notes :

Unlike the @alan-kilborn’s solution, this S/R does not care about numbers, under the name = ••• line and about text after _section_, too. It just try to match any %s string and stores the first XXX string found, before _section, for use in replacement
Note that if NO block with a line name = "XXX_section_xxx" can be found in a whole section ( case m = 0 ), all strings s%, in lines name = "s%_section_xxx" of this section, would be changed as XXX, where XXX comes from the first name = "XXX_section_xxx" line of the next section

Best Regards,

guy038

Ramanand Jhingade

@guy038 I have to add 9 lines of matter (text), all on new lines, one after the other in multiple files after this code/text: <button class=“button-top”><i class=“fa fa-chevron-up”></i></button> - how do I do it?

PeterJones

@Ramanand-Jhingade said in Adding text with variable on several files:

all on new lines, one after the other

Using \r\n in the REPLACE field indicates the CRLF newline. (If you’re editing a file with a linux LF newline, just use \n).

So if you wanted the replacement to be

blah
second line
third line

then REPLACE would be blah\r\nsecond line\r\nthird line

Ramanand Jhingade

@Ramanand-Jhingade The only solution I can think of now is to use the “Extended” mode of search, search for <button class=“button-top”><i class=“fa fa-chevron-up”></i></button> and replace it with <button class=“button-top”><i class=“fa fa-chevron-up”></i></button>\nxxxxxxxxx where xxxxxxxxx is the new line for each line, 9 times but is there a way to do it all together?
Apart from what @PeterJones typed above?

PeterJones

@Ramanand-Jhingade ,

Sorry, yes, my reply was assuming Regular Expression mode, because that’s the mode that was being used in the conversation between @Vincent-Perez and @guy038 – I didn’t realize when I replied that you weren’t the original poster.

With 9 lines, you will just have to have nine instances of \r\nxxxxxxx in the replacement.

To avoid some duplication of data, I suggest you use the $0 replacement (see docs), which will use the value matched from the FIND, rather than manually retyping that initial data that you want to keep:

FIND = <button class="button-top"><i class="fa fa-chevron-up"></i></button>
REPLACE = $0\r\nline 1\r\nline2\r\nline3\r\nline 4\r\nline 5\r\nline six\r\nline 7\r\nline eight\r\nline 9!
SEARCH MODE = regular expression

(I continue to use \r\n in my examples, because chances are, since you’re editing files on using a windows application, the newlines are probably windows-style CRLF newlines)

Ramanand Jhingade

@PeterJones Wonderful but do I need that exclamation mark at the end (in the REPLACE field)?

Alan Kilborn

@Ramanand-Jhingade said in Adding text with variable on several files:

but do I need that exclamation mark at the end (in the REPLACE field)?

Only if you want it there.
Honestly, some experimentation will quickly provide the answer to that, rather than asking here and waiting the time it takes for a response.

Ramanand Jhingade

@Alan-Kilborn Yes, you’re right. Thanks for the help @Alan-Kilborn @PeterJones and @guy038